Lead rings? Here's why
Moderators: gds, bakerjw, Dolomite_Supafly
- Dolomite_Supafly
- Silent But Deadly
- Posts: 3017
- Joined: Fri Oct 30, 2009 7:03 am
- Location: East Tennessee
- Contact:
Lead rings? Here's why
I have seen various posts over the years talking about lead rings. The reason is the brass is not long enough for the chamber when shooting cast bullets. The bullets will get shaved by the chamber edge or just get squished to fill the gap.
The picture above is a gap between the brass and the step in the chamber that the case mouth should be closer to. This barrel never had a lead ring issue because of the champfer but some barrels have a 90 degree edge which I believe shaves off the lead or coating as it passes and what gets shaved off fills that gap.
WWW.thegunmilitia.com
Come join the militia!
Come join the militia!
- Bob the nailer
- Silent But Deadly
- Posts: 277
- Joined: Mon Aug 15, 2016 6:03 am
- Location: Michigan
- Contact:
Re: Lead rings? Here's why
As always excellent information!
One ragged hole! The quest for accuracy continues...
Bob the nailer
NRA Life member
Varmint Hunters Assoc. Member
American Gunsmith Association
www.knowyourzero.com
Bob the nailer
NRA Life member
Varmint Hunters Assoc. Member
American Gunsmith Association
www.knowyourzero.com
- bangbangping
- Silent But Deadly
- Posts: 2695
- Joined: Sun Sep 15, 2013 6:34 pm
- Location: Texas Gulf Coast
Re: Lead rings? Here's why
I believe this is even more important than the length of the brass. I'm fighting a barrel right now that will shave anything sized over .308, even with brass that's trimmed to 1.368. My guess (hasn't been fully proven) is that the powder matters, too. More chance of a ring with higher pressures.Dolomite_Supafly wrote: ↑Mon Sep 09, 2019 10:47 am This barrel never had a lead ring issue because of the champfer but some barrels have a 90 degree edge which I believe shaves off the lead or coating as it passes and what gets shaved off fills that gap.
By the way, what scope are you using? That's a great photo.
Re: Lead rings? Here's why
Fire-lapping will usually take care of the issue and has increased accuracy for me.
I use soft lead bullets that fill the throat impregnated with 320 grit grease rolled between 2 strips of iron plate.
Then load the bullets over just enough powder to make sure they get out the barrel.
6 to 700 fps will work well.
AR's need the gas block turned upside down to keep the grit out of the gas system.
I got a kit from beartooth bullets years ago and he has write ups about doing it in more detail.
I use soft lead bullets that fill the throat impregnated with 320 grit grease rolled between 2 strips of iron plate.
Then load the bullets over just enough powder to make sure they get out the barrel.
6 to 700 fps will work well.
AR's need the gas block turned upside down to keep the grit out of the gas system.
I got a kit from beartooth bullets years ago and he has write ups about doing it in more detail.
- bangbangping
- Silent But Deadly
- Posts: 2695
- Joined: Sun Sep 15, 2013 6:34 pm
- Location: Texas Gulf Coast
Re: Lead rings? Here's why
How many bullets would you use in a situation like this?45r wrote: ↑Wed Sep 11, 2019 4:52 pm Fire-lapping will usually take care of the issue and has increased accuracy for me.
I use soft lead bullets that fill the throat impregnated with 320 grit grease rolled between 2 strips of iron plate.
Then load the bullets over just enough powder to make sure they get out the barrel.
6 to 700 fps will work well.
AR's need the gas block turned upside down to keep the grit out of the gas system.
I got a kit from beartooth bullets years ago and he has write ups about doing it in more detail.
In the CVA pistol the powder definitely makes a difference. With NOE 247 sub loads I've been using N105 which, according to Quickload, is generating 20K psi. And it's 19K by 1/2" of bullet travel, before the bullet is fully in the throat. My alloy is pretty soft, so that pressure apparently is enough to bump up the bullet diameter so it scrapes on the neck/throat transition. With a slower powder the ring is less or goes away completely. I don't want to use a harder alloy or slower powder so I'm going to try the fire lapping and will report back.
Re: Lead rings? Here's why
I only do a few with rifles and check how far the throat has moved forward.
You don't want to move it too far forward.
Just enough to smooth out the sharp edge
In front of the neck.
Don't use bore-rider bullets.
They don't work well for fire-lapping.
The slower the better.
Just enough to get out the barrel.
Clean barrel after each 3 shots and stop when throat moves forward around 20 thou.
The sharp edge should be gone and the throat smoothed out to not shear cast bullets.
You don't want to move it too far forward.
Just enough to smooth out the sharp edge
In front of the neck.
Don't use bore-rider bullets.
They don't work well for fire-lapping.
The slower the better.
Just enough to get out the barrel.
Clean barrel after each 3 shots and stop when throat moves forward around 20 thou.
The sharp edge should be gone and the throat smoothed out to not shear cast bullets.
-
- Silent But Deadly
- Posts: 1215
- Joined: Mon Oct 17, 2011 8:09 am
- Location: NW Florida
Re: Lead rings? Here's why
What bore scope did you use to get that sharp photo with?Dolomite_Supafly wrote: ↑Mon Sep 09, 2019 10:47 am
I have seen various posts over the years talking about lead rings. The reason is the brass is not long enough for the chamber when shooting cast bullets. The bullets will get shaved by the chamber edge or just get squished to fill the gap.
The picture above is a gap between the brass and the step in the chamber that the case mouth should be closer to. This barrel never had a lead ring issue because of the champfer but some barrels have a 90 degree edge which I believe shaves off the lead or coating as it passes and what gets shaved off fills that gap.
Thanks,
- Dolomite_Supafly
- Silent But Deadly
- Posts: 3017
- Joined: Fri Oct 30, 2009 7:03 am
- Location: East Tennessee
- Contact:
Re: Lead rings? Here's why
https://www.amazon.com/gp/product/B07TT ... UTF8&psc=1Whole Bunches wrote: ↑Tue Oct 22, 2019 10:03 amWhat bore scope did you use to get that sharp photo with?Dolomite_Supafly wrote: ↑Mon Sep 09, 2019 10:47 am
I have seen various posts over the years talking about lead rings. The reason is the brass is not long enough for the chamber when shooting cast bullets. The bullets will get shaved by the chamber edge or just get squished to fill the gap.
The picture above is a gap between the brass and the step in the chamber that the case mouth should be closer to. This barrel never had a lead ring issue because of the champfer but some barrels have a 90 degree edge which I believe shaves off the lead or coating as it passes and what gets shaved off fills that gap.
Thanks,
They are definately worth the money. They have great CS as well. I folded mine up too many times and broke it, they replaced it for free.
WWW.thegunmilitia.com
Come join the militia!
Come join the militia!
- wildfowler
- Silent But Deadly
- Posts: 703
- Joined: Sun Mar 30, 2008 8:40 am
- Location: Mis'sippi
Re: Lead rings? Here's why
I thought you were going to tell us that was a $600 Hawkeye. I ordered that. For 50 bucks, why not?
Frankly it looks better than some of the Hawkeye photos I’ve seen.
Thank you.
Frankly it looks better than some of the Hawkeye photos I’ve seen.
Thank you.
driven every kind of rig that's ever been made, driven the backroads so I wouldn't get weighed. - Lowell George
- Dolomite_Supafly
- Silent But Deadly
- Posts: 3017
- Joined: Fri Oct 30, 2009 7:03 am
- Location: East Tennessee
- Contact:
Re: Lead rings? Here's why
Yeah, I wasn't expecting much because of all the other <$50 bore scopes I have bought in the past. It has a big long thread on another website with nothing but positive things to say about it. It has helped me start figuring out why some Savages shoot great while others do not. I am also cataloging pictures of as many barrels as I can now. I tell all my friends to bring their barrels over so I can scope them. I am currently getting pictures of an AR in 223 every 200 rounds to see what sort of throat erosion and wear it has. I also plan on doing the same to a 6 Creedmoor I am about to build.
The only thing I will say is once you unfurl it leave it unfurled. I have spoke to a few other users and they have had their's replaced numerous times because of coiling it up over and over.
The only thing I will say is once you unfurl it leave it unfurled. I have spoke to a few other users and they have had their's replaced numerous times because of coiling it up over and over.
WWW.thegunmilitia.com
Come join the militia!
Come join the militia!
Who is online
Users browsing this forum: No registered users and 58 guests