300BlkTalk

Rifle used: Handi rifle AAC
Barrel: 16" 1:7
Bullet: Lee C-309-120-R mold Powder coated and sized to .311
Powder used: Trail Boss
COAL: 1.640"
Primer: CCI Small rifle
Cases: converted .223 LC

4.2 grains 1042 1046 1050 1033 1038
4.6 grains 1069 1067 1046 1065 1062

Rifle Used : Cva scout
Barrel maker: Bergara
Barrel Length and Twist : 16" 1:8
Bullet Used (Grain, Manufacturer, Type) : 150, Everglade, flat point
Powder Charge and Brand : 6.5 +/- 0.1- Lil gun
Case Used : 5.56 Blank converted 1.360"
Primer Used : WSR
COAL: 1.910
Chronograph Velocity: Average 1012
Notes: Very quiet and also shoot well out of a factory R700 aac-sd

Ive been sub-plinking with these for a while. About the cheapest I have found for killing paper.

http://www.evergladesammo.com/bullets/r ... llets.html

Shot some LUCKY13 green Zombie 123's today. At 50 yards 5 round groups were 2" or better.

Rifle Used : REM 700 300 AAC Blackout 16"
Bullet Used (Grain, Manufacturer, Type) : LUCKY13 123 grain zombie
Powder Charge and Brand : 4.6 gr Trail Boss
Case Used : 5.56 Blank converted 1.358"
OAL : 1.940
Primer Used : cci small rifle
Notes: need to run it over the chrony and check the noise level....


Also shot some Extreme 150's but the groups were terrible....
5.5 grns of Trail Boss at 1.988"
Will need to play with this one to get better accuracy out of it....

I bought a Lee mold for the .32 Colt. They're supposed to be 93g and .311 but with the alloy I'm using, they come out 87g and .310". So far I've only loaded them over 2.5g or Red Dot and a Win small pistol primer. They shoot good but I'm clueless about how fast they're going...

Anyway I think this mold is a killer deal for the blackout if you don't mind casting your own. I sized the first batch to .309 but after this, I'm not going to bother sizing them...

Tony

Rifle used: Micro 7
Barrel: 16" 1:7, Suppressed
Bullet: Hornady .308 XTP, 90 grain
Powder used: Tin Star
CBTO: 1.598" (~.025" off lands)
Primer: CCI 400
Cases: Lapua

4.5 grains (5 shots) - Avg: 1013, ES: 18.4, SD: 8.5 Approx. 1" @ 50 yards

A friend of mine powder coated some of my bullets from mt Lee 311-93-1R mold for the .32 revolver then shot them over a chronograph.

3gr of of Red Dot produced around 1050fps,
2.5gr produced around 900fps
2.0gr produced 760fps

I had been loading them with 2.0g of Red Dot but after this I'm going to stick with 3.0g. He reported better accuracy with the warmer load but that could have been a fluke. The 2.0g loads with Alox lubed bullets have been very accurate out of my Handi Rifle...

Tony

AR pistol
10" Kak 1:8 barrel - no hand guard.
CCI srp
5gr. CFE pistol
Hornady half jacket 100 gr.
Converted brass
Loaded with half of jacket in the neck.
SeeAll sight
Guessing 950 fps
Sounds like my 177 without a pellet. Pop.
Feeds fine from Pmag but gas is turned down so no ejection.
About 3" @ 25 yds standing.

Nosler 190
Any "size" 300 case.
OAL ~2.20"
10.3 grains of Hodgdon 4198
CCI Small Rifle Primer

~1040fps on average.

I also loaded 11.3 grains and the bullet broke the sound barrier.

Single shot only.

Rifle Used : Remington 700 SPS Tactical 16" with AAC flash hider
Barrel maker: Remington
Barrel Length and Twist : 16" 1:7
Bullet Used (Grain, Manufacturer, Type) : Everglades Ammo 30 Carbine, 110 grain
Powder Charge and Brand : 5.4 gr Trail Boss
Case Used : 300BO factory case (once fired, unsure of brand)
Primer Used : CCI Small Rifle
COAL: 1.885 in
Chronograph Velocity: Unsure of FPS, as I don't have a chrono, and don't know anyone in my area with one.
Notes: Very quiet, even unsuppressed, and very little kick, I'm willing to say an air gun has more kick to it. Single shot only, haven't tried to feed it from the magazine yet.

I'm going to bump this thread for new recipes.

I really liked the LUCKY13 green Zombie 123, but they're no longer available.

Just curious as to what folks are using as a replacement.