Use these blocks to hold the lower so you can do maintenance and to test your trigger work. You can dry fire the lower without fear of damaging the receiver because the hammer will hit the plastic block not the thin aluminum.
(I put silver paint on the edge of the hammer for you to see it better, that is not a gap.)
You can also mount an upper (with no BCG) on the lower with the block installed.
The lower half of the block is trimmed down so repeated clamping should not interfere with it being removed from the magwell.
POST here that you will take one.
This batch only are $25 shipped ppal fees included.
ppal to vonzep58(AT)yahoo.com
COMBO DEAL for next few days
Jig and pack block = $75 shipped ppal fees included ($10 off)
Buy a pack block lock and a lower vice block= $60 ($5 off)
block and jig=$60 ($10 off)
lower vise Buy tall three, the case jig to cut BO brass, the pack block to store your AR in a Go Bag and the lower vise block and its $95 and I will throw in priority shipping
pack block link
viewtopic.php?f=179&t=82863
Cut off tool link
viewtopic.php?f=179&t=80842&p=756842#p756842
Lower vise block and hammer block for sale *all sold****
Moderators: gds, bakerjw, renegade, tba02
- vz58
- Silent But Deadly
- Posts: 1437
- Joined: Fri Jul 29, 2011 11:57 am
- Location: Smack dab in the middle of NC
Lower vise block and hammer block for sale *all sold****
Last edited by vz58 on Tue Apr 02, 2013 10:00 pm, edited 6 times in total.
Re: Lower vise block and hammer block for sale
I'll take one. Payment is sent PP. Thanks, Andy
Re: Lower vise block and hammer block for sale
I'll take the last onevz58 wrote:One left!
Bill Harris
- FirefighterCT
- Silent But Deadly
- Posts: 394
- Joined: Tue Jun 26, 2012 2:57 pm
- Location: CT, the Unconstitutional State.
Re: Lower vise block and hammer block for sale
Another great looking product David. The hammer block is a great idea and solves a common problem found in every other lower vise block that I've seen.
Re: Lower vise block and hammer block for sale
I'l take one. PM sent
- vz58
- Silent But Deadly
- Posts: 1437
- Joined: Fri Jul 29, 2011 11:57 am
- Location: Smack dab in the middle of NC
Re: Lower vise block and hammer block for sale
Cajun22 and 300black0ut have a block held back for them each.
All gone
I will clean up the Gcode and cut some more pretty soon. These were the last of the test batch but are 100% just fine.
All gone
I will clean up the Gcode and cut some more pretty soon. These were the last of the test batch but are 100% just fine.
- vz58
- Silent But Deadly
- Posts: 1437
- Joined: Fri Jul 29, 2011 11:57 am
- Location: Smack dab in the middle of NC
Re: Lower vise block and hammer block for sale
Had insomnia, made a small batch last night.
$25 shipped ppal, I will try to keep some on hand.
$25 shipped ppal, I will try to keep some on hand.
- Overton-AR
- Silent But Deadly
- Posts: 1191
- Joined: Tue Nov 03, 2009 4:16 am
Re: Lower vise block and hammer block for sale **in stock**
I'll take one.....PP sent. Thanks.
-
- New Member
- Posts: 1
- Joined: Mon Feb 18, 2013 2:10 pm
Re: Lower vise block and hammer block for sale **in stock**
I'll take one, PP sent Stiff Finger
Who is online
Users browsing this forum: No registered users and 176 guests