**THE ORIGINAL FASTEST BLACKOUT JIG ** IN STOCK****
Posted: Sun Sep 16, 2012 5:13 pm
The only jig featured in publications on reloading!
Look at "Making Ammo, a beginners guide to handloading" by Kyle Lynch and 2nd amendment media!!!
Page 115
WE HAVE MANY DIFFERENT JIGS AND PRODUCTS. IF YOU DON'T SEE A JIG FOR YOUR CALIBER NEEDS EMAIL OR PM US!!
VIDEO of an 11 year old knocking out 30 cases a minute with 5 minutes of practice.
All jigs except the custom 308 jig simply bolts in with the supplied bolts and greatly speeds and "standardizes" the rough cut off operation. Using this jig gives you a rough cut case a few thousands long with a nice even mouth. No more uneven mouths catching on the final trimmer! THESE BOLT IN ROCK SOLID! no need for "stabilizers" like other designs need! Design and build it right the first time and you dont need extra pieces to try to fix it!
The just cut case gets ejected under spring power out the right side a couple inches and the next snaps in place!
This means your right hand never has to leave the saw handle and your left hand is feeding the cases.
I usually shoot a little shot of thin lubricant (Hornady one shot, silicone lube etc) into the jig before using if it has been sitting a few days and everything runs smoothly.
PLEASE NO PAYPAL GIFTS!!!
_____________________________________________________________________________________________________
HARD COAT BLACK ANODIZED 300 BLACKOUT JIGS $37
These are $37 shipped and paypal fees included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
IN STOCK
______________________________________________________________________________________________________
HARD COAT BLACK ANODIZED COSMETICALLY BLEMISHED BLACKOUT JIGS $32
Jigs that may deeper than normal clamp marks, minor chatter on a cut, discolored or pitted anodizing 100% functionally equivalent to the other, normal jig.
These are $32 shipped and paypal fees included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
IN STOCK
_______________________________________________________________________________________________________
HARD COAT BLACK ANODIZED 5.56 to 7.62x25 Tokarov jigs finished and hard anodized, $30
HARD COAT BLACK ANODIZED 5.56 to TCM 22 jigs hard anodized , $30
HARD COAT BLACK ANODIZED 5.56 to 7.62x40 WT jigs, hard anodized $30
_______________________________________________________________________________________________________
HARD COAT ANODIZED BULLET SWAGING JIGS! .40 S&W and 357 Sig trim to use as .45 ACP bullet jackets? Sure thing, they are $35
HARD COAT ANODIZED BULLET SWAGING JIGS! 9mm trim to use as .40 S&W bullet jackets? Sure thing, they are $35
_______________________________________________________________________________________________________
2 LEFT
We also have SLOTTED Sheridan Case gauges. Add $55 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They are $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
WHAT IS A SLOTTED SHERIDAN AMMO GAUGE!!?!?!?
Well look right here! I will embed it later...... Just cut and paste!
http://www.youtube.com/watch?v=OKyM4O4vsWg
_______________________________________________________________________________________________________
IN STOCK
Want a non slotted Sheridan ammo gauge?
Add $35 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $37 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
______________________________________________________________________________________________________
I out of stock! (limited numbers)
We also have [color=#FF0000S].223 SLOTTED sheridan Case gauges. Add $55 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
_______________________________________________________________________________________________________
.223 AMMO GAUGE
IN STOCK!!(Limited numbers)
Want a non slotted .223 Sheridan ammo gauge? INSTOCK
Add $35 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $37 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
_______________________________________________________________________________________________________
308 SLOTTED SHERIDAN
IN STOCK!!
We also have 308 SLOTTED Sheridan Case gauges. They are $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
WHAT IS A SLOTTED SHERIDAN AMMO GAUGE!!?!?!?
Well look right here! I will embed it later...... Just cut and paste!
http://www.youtube.com/watch?v=OKyM4O4vsWg
_______________________________________________________________________________________________________
.308/30-06 family JIGS
Jigs for this family for cutting down 30-06/.308 cases /fired blanks to make:
7.92x57
7.92x33
.308
45 shot shell
44 automag
custom lengths
$35 shipped paypal fees included just PM or email me for specifics!
______________________________________________________________________________________________________
EASY ID MAGAZINE BANDS
The normal 300 band
5 for $10.95!
________________________________________________________________________________________
EASY ID MAGAZINE BANDS
_
The NEW grey green 300 band
5 for $10.95!_________________________________________________________________________
_____________________________
EASY ID MAGAZINE BANDS
RED SUPER and raised black SUB bands
OUT OF STOCK
_______________________________________________________________________________________________________
EASY ID MAGAZINE BANDS
Light brown bands
5 for $10.95
_________________________________________________________________________________________________
5 for $10.95
_______________________________________________________________________________________________________
SAW OPTIONS:
Yes our jig can be used with several different available saws unlike the other jigs!
Here's the saw they are designed for.
Hsrbor Freight has the saws under other part numbers too
Or you can use this high quality saw by another national hobby chain
http://www.micromark.com/microlux-mini- ... ,9639.html
Or this inexpensive Harbor freight saw: ($24-$36 depending on sales)
THANKS TO OVERTON AR FOR THIS GREAT IDEA> WAY CHEAPER THAN THE OVER PRICED "ANACONDA" SAWS AND VERSITAL TOO
______________________________________________________________________________________________________________
THIS IS THE VIDEO, CLICK THE PICTURE
_______________________________________________________________________________________________________________
Ppal to [email protected] do not assume ppal puts your address on the pmt info. sometimes it does not.
I ship in order of payment received, if you want to USPS MO I will add you in line at time of receipt.
I can also do credit cards
I pride myself on fast shipping, I often ship the same day, HOWEVER, please understand I have a "real" job and it can delay me from mailing for a couple of business days. I ship first class with tracking info. I cannot realistically get everyone a tracking number PM'd to them but if you are worried about your jig please PM me and we will track it.
_________________________________________________________________________________________________________________
Here are the installation instructions, please read them if you buy the jig they really do help it go quickly.
UNPLUG THE SAW.
Remove the thumb screw on the left side of the clamp, catch and save the little nut that falls out from underneath, you'll need it later.
Rock the clamp assembly until it comes out, set aside.
The hole that used to have the pivot in it (right side) will need to use the "skinny bolt and nut" included in the jig package. Just insert the skinny bolt FROM THE BOTTOM and put the nut on top of the jig
Install the left side bolt and the nut you saved from earlier.
I would strongly suggest you not remove the saw unit from the base, the return spring can be difficult to reinstall.
Make sure the saw blade is tight and not on backwards, this is the cause of almost all slow cutting and saw burn out.
Next lower the saw blade and slide the jig up to about the thickness of a 3x5" index card (.010") from the side of the blade.
Let the saw blade go up while holding the jig in place. Snug the right bolt.
Now push the left side of the jig back towards the saw's hinge slightly. The jig should be SLIGHTLY crooked when you look down on it.
Tighten the left bolt then the right.
Clamp, bolt, screw or otherwise secure the saw to the work bench.
*********Spray with a light lubricant.************
Cut a test piece of brass. I like to cut them to about 1.365" to 1.370" and then finish trim them.
If the brass is too long or short for your taste adjust the jig towards or away from the blade as needed.
If the brass mouth is cut at an angle, adjust the left side of the jig as needed to correct.
Before you turn on the saw and start cutting a bunch of cases, practice the insertion of brass several times to get a feel for it.
Sizing the brass first will often speed things up, it removes the little bulges that can slow ejection. Also run a swab or bore brush through the jig periodically to wipe out trash.
As you use and lube the jig, case operation will get noticeably smoother and faster.
WEB SITE IS UP!!!
http://www.zepprecisionmachines.com/
Order here or there, the price is slightly higher on the web site as they charge a percentage for every sale.
PLEASE NO PAYPAL GIFTS!!!
Look at "Making Ammo, a beginners guide to handloading" by Kyle Lynch and 2nd amendment media!!!
Page 115
WE HAVE MANY DIFFERENT JIGS AND PRODUCTS. IF YOU DON'T SEE A JIG FOR YOUR CALIBER NEEDS EMAIL OR PM US!!
VIDEO of an 11 year old knocking out 30 cases a minute with 5 minutes of practice.
All jigs except the custom 308 jig simply bolts in with the supplied bolts and greatly speeds and "standardizes" the rough cut off operation. Using this jig gives you a rough cut case a few thousands long with a nice even mouth. No more uneven mouths catching on the final trimmer! THESE BOLT IN ROCK SOLID! no need for "stabilizers" like other designs need! Design and build it right the first time and you dont need extra pieces to try to fix it!
The just cut case gets ejected under spring power out the right side a couple inches and the next snaps in place!
This means your right hand never has to leave the saw handle and your left hand is feeding the cases.
I usually shoot a little shot of thin lubricant (Hornady one shot, silicone lube etc) into the jig before using if it has been sitting a few days and everything runs smoothly.
PLEASE NO PAYPAL GIFTS!!!
_____________________________________________________________________________________________________
HARD COAT BLACK ANODIZED 300 BLACKOUT JIGS $37
These are $37 shipped and paypal fees included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
IN STOCK
______________________________________________________________________________________________________
HARD COAT BLACK ANODIZED COSMETICALLY BLEMISHED BLACKOUT JIGS $32
Jigs that may deeper than normal clamp marks, minor chatter on a cut, discolored or pitted anodizing 100% functionally equivalent to the other, normal jig.
These are $32 shipped and paypal fees included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
IN STOCK
_______________________________________________________________________________________________________
HARD COAT BLACK ANODIZED 5.56 to 7.62x25 Tokarov jigs finished and hard anodized, $30
HARD COAT BLACK ANODIZED 5.56 to TCM 22 jigs hard anodized , $30
HARD COAT BLACK ANODIZED 5.56 to 7.62x40 WT jigs, hard anodized $30
_______________________________________________________________________________________________________
HARD COAT ANODIZED BULLET SWAGING JIGS! .40 S&W and 357 Sig trim to use as .45 ACP bullet jackets? Sure thing, they are $35
HARD COAT ANODIZED BULLET SWAGING JIGS! 9mm trim to use as .40 S&W bullet jackets? Sure thing, they are $35
_______________________________________________________________________________________________________
2 LEFT
We also have SLOTTED Sheridan Case gauges. Add $55 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They are $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
WHAT IS A SLOTTED SHERIDAN AMMO GAUGE!!?!?!?
Well look right here! I will embed it later...... Just cut and paste!
http://www.youtube.com/watch?v=OKyM4O4vsWg
_______________________________________________________________________________________________________
IN STOCK
Want a non slotted Sheridan ammo gauge?
Add $35 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $37 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
______________________________________________________________________________________________________
I out of stock! (limited numbers)
We also have [color=#FF0000S].223 SLOTTED sheridan Case gauges. Add $55 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
_______________________________________________________________________________________________________
.223 AMMO GAUGE
IN STOCK!!(Limited numbers)
Want a non slotted .223 Sheridan ammo gauge? INSTOCK
Add $35 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $37 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
_______________________________________________________________________________________________________
308 SLOTTED SHERIDAN
IN STOCK!!
We also have 308 SLOTTED Sheridan Case gauges. They are $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
WHAT IS A SLOTTED SHERIDAN AMMO GAUGE!!?!?!?
Well look right here! I will embed it later...... Just cut and paste!
http://www.youtube.com/watch?v=OKyM4O4vsWg
_______________________________________________________________________________________________________
.308/30-06 family JIGS
Jigs for this family for cutting down 30-06/.308 cases /fired blanks to make:
7.92x57
7.92x33
.308
45 shot shell
44 automag
custom lengths
$35 shipped paypal fees included just PM or email me for specifics!
______________________________________________________________________________________________________
EASY ID MAGAZINE BANDS
The normal 300 band
5 for $10.95!
________________________________________________________________________________________
EASY ID MAGAZINE BANDS
_
The NEW grey green 300 band
5 for $10.95!_________________________________________________________________________
_____________________________
EASY ID MAGAZINE BANDS
RED SUPER and raised black SUB bands
OUT OF STOCK
_______________________________________________________________________________________________________
EASY ID MAGAZINE BANDS
Light brown bands
5 for $10.95
_________________________________________________________________________________________________
5 for $10.95
_______________________________________________________________________________________________________
SAW OPTIONS:
Yes our jig can be used with several different available saws unlike the other jigs!
Here's the saw they are designed for.
Hsrbor Freight has the saws under other part numbers too
Or you can use this high quality saw by another national hobby chain
http://www.micromark.com/microlux-mini- ... ,9639.html
Or this inexpensive Harbor freight saw: ($24-$36 depending on sales)
THANKS TO OVERTON AR FOR THIS GREAT IDEA> WAY CHEAPER THAN THE OVER PRICED "ANACONDA" SAWS AND VERSITAL TOO
______________________________________________________________________________________________________________
THIS IS THE VIDEO, CLICK THE PICTURE
_______________________________________________________________________________________________________________
Ppal to [email protected] do not assume ppal puts your address on the pmt info. sometimes it does not.
I ship in order of payment received, if you want to USPS MO I will add you in line at time of receipt.
I can also do credit cards
I pride myself on fast shipping, I often ship the same day, HOWEVER, please understand I have a "real" job and it can delay me from mailing for a couple of business days. I ship first class with tracking info. I cannot realistically get everyone a tracking number PM'd to them but if you are worried about your jig please PM me and we will track it.
_________________________________________________________________________________________________________________
Here are the installation instructions, please read them if you buy the jig they really do help it go quickly.
UNPLUG THE SAW.
Remove the thumb screw on the left side of the clamp, catch and save the little nut that falls out from underneath, you'll need it later.
Rock the clamp assembly until it comes out, set aside.
The hole that used to have the pivot in it (right side) will need to use the "skinny bolt and nut" included in the jig package. Just insert the skinny bolt FROM THE BOTTOM and put the nut on top of the jig
Install the left side bolt and the nut you saved from earlier.
I would strongly suggest you not remove the saw unit from the base, the return spring can be difficult to reinstall.
Make sure the saw blade is tight and not on backwards, this is the cause of almost all slow cutting and saw burn out.
Next lower the saw blade and slide the jig up to about the thickness of a 3x5" index card (.010") from the side of the blade.
Let the saw blade go up while holding the jig in place. Snug the right bolt.
Now push the left side of the jig back towards the saw's hinge slightly. The jig should be SLIGHTLY crooked when you look down on it.
Tighten the left bolt then the right.
Clamp, bolt, screw or otherwise secure the saw to the work bench.
*********Spray with a light lubricant.************
Cut a test piece of brass. I like to cut them to about 1.365" to 1.370" and then finish trim them.
If the brass is too long or short for your taste adjust the jig towards or away from the blade as needed.
If the brass mouth is cut at an angle, adjust the left side of the jig as needed to correct.
Before you turn on the saw and start cutting a bunch of cases, practice the insertion of brass several times to get a feel for it.
Sizing the brass first will often speed things up, it removes the little bulges that can slow ejection. Also run a swab or bore brush through the jig periodically to wipe out trash.
As you use and lube the jig, case operation will get noticeably smoother and faster.
WEB SITE IS UP!!!
http://www.zepprecisionmachines.com/
Order here or there, the price is slightly higher on the web site as they charge a percentage for every sale.
PLEASE NO PAYPAL GIFTS!!!