300BlkTalk

All things 300 AAC BLACKOUT
It is currently Sat Sep 20, 2014 5:57 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 1133 posts ]  Go to page 1, 2, 3, 4, 5 ... 114  Next
Author Message
PostPosted: Sun Sep 16, 2012 5:13 pm 
Online
Silent But Deadly
User avatar

Joined: Fri Jul 29, 2011 11:57 am
Posts: 892
Location: Smack dab in the middle of NC
WE HAVE MANY DIFFERENT JIGS AND PRODUCTS. IF YOU DON'T SEE A JIG FOR YOUR CALIBER NEEDS EMAIL OR PM US!!

All jigs except the custom 308 jig simply bolts in with the supplied bolts and greatly speeds and "standardizes" the rough cut off operation. Using this jig gives you a rough cut case a few thousands long with a nice even mouth. No more uneven mouths catching on the final trimmer! THESE BOLT IN ROCK SOLID! no need for "stabilizers" like other designs need! Design and build it right the first time and you dont need extra pieces to try to fix it!

The just cut case gets ejected under spring power out the right side a couple inches and the next snaps in place!

This means your right hand never has to leave the saw handle and your left hand is feeding the cases.
I usually shoot a little shot of thin lubricant (Hornady one shot, silicone lube etc) into the jig before using if it has been sitting a few days and everything runs smoothly.
PLEASE NO PAYPAL GIFTS!!!
_____________________________________________________________________________________________________


HARD COAT BLACK ANODIZED 300 BLACKOUT JIGS $39

Image

These are $39 shipped and paypal fees included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.

IN STOCK
______________________________________________________________________________________________________

HARD COAT BLACK ANODIZED COSMETICALLY BLEMISHED BLACKOUT JIGS $35

Image

Jigs that may deeper than normal clamp marks, minor chatter on a cut, discolored or pitted anodizing 100% functionally equivalent to the other, normal jig.

These are $35 shipped and paypal fees included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.

IN STOCK

_______________________________________________________________________________________________________

HARD COAT BLACK ANODIZED 5.56 to 7.62x25 Tokarov jigs finished and hard anodized, $30

HARD COAT BLACK ANODIZED 5.56 to TCM 22 jigs hard anodized , $30

HARD COAT BLACK ANODIZED 5.56 to 7.62x40 WT jigs, hard anodized $30


_______________________________________________________________________________________________________

HARD COAT ANODIZED BULLET SWAGING JIGS! .40 S&W and 357 Sig trim to use as .45 ACP bullet jackets? Sure thing, they are $35
Image

HARD COAT ANODIZED BULLET SWAGING JIGS! 9mm trim to use as .40 S&W bullet jackets? Sure thing, they are $35
Image



_______________________________________________________________________________________________________




Image

out of STOCK!!
We also have SLOTTED Sheridan Case gauges. Add $55 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They are $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.

WHAT IS A SLOTTED SHERIDAN AMMO GAUGE!!?!?!?
Well look right here! I will embed it later...... Just cut and paste!


http://www.youtube.com/watch?v=OKyM4O4vsWg
_______________________________________________________________________________________________________


IN STOCK!!
Want a non slotted Sheridan ammo gauge?
Image

Add $35 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $37 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.


______________________________________________________________________________________________________

IN STOCK!! (limited numbers)
We also have [color=#FF0000S].223 SLOTTED heridan Case gauges. [/color] Add $55 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.Image

_______________________________________________________________________________________________________
.223 AMMO GAUGE
IN STOCK!!(Limited numbers)
Want a non slotted .223 Sheridan ammo gauge? OUT OF STOCK
Image

Add $35 to any jig purchase and we will throw one in! If you want one outright without a jig shipped at the same time to the same address as a jig? They a e $37 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.
_______________________________________________________________________________________________________
308 SLOTTED SHERIDANImage

IN STOCK!!
We also have 308 SLOTTED Sheridan Case gauges. They are $59 total paypal fees and shipping included. Dont want to paypal? Want to use a credit card? or USPS MO? PM for address.

WHAT IS A SLOTTED SHERIDAN AMMO GAUGE!!?!?!?
Well look right here! I will embed it later...... Just cut and paste!


http://www.youtube.com/watch?v=OKyM4O4vsWg

_______________________________________________________________________________________________________
.308/30-06 family JIGS


Jigs for this family for cutting down 30-06/.308 cases /fired blanks to make:
7.92x57
7.92x33
.308
45 shot shell
44 automag
custom lengths
$35 shipped paypal fees included just PM or email me for specifics!

______________________________________________________________________________________________________

EASY ID MAGAZINE BANDS

Image

The normal 300 band
5 for $10.95!

_______________________________________________________________________________________________________

EASY ID MAGAZINE BANDS

Image

RED SUPER and raised black SUB bands

5 for $11.95

_______________________________________________________________________________________________________

EASY ID MAGAZINE BANDS


Image

Light brown bands
5 for $10.95
_________________________________________________________________________________________________

Image


5 for $10.95

_______________________________________________________________________________________________________
SAW OPTIONS:

Yes our jig can be used with several different available saws unlike the other jigs!


Here's the saw they are designed for.
Hsrbor Freight has the saws under other part numbers too



Image



Or you can use this high quality saw by another national hobby chain

http://www.micromark.com/microlux-mini- ... ,9639.html


Or this inexpensive Harbor freight saw: ($24-$36 depending on sales)
Image

Image




THANKS TO OVERTON AR FOR THIS GREAT IDEA> WAY CHEAPER THAN THE OVER PRICED "ANACONDA" SAWS AND VERSITAL TOO
Image
______________________________________________________________________________________________________________

THIS IS THE VIDEO, CLICK THE PICTURE


Image


_______________________________________________________________________________________________________________

Ppal to vonzep58@yahoo.com do not assume ppal puts your address on the pmt info. sometimes it does not.


I ship in order of payment received, if you want to USPS MO I will add you in line at time of receipt.

I can also do credit cards

I pride myself on fast shipping, I often ship the same day, HOWEVER, please understand I have a "real" job and it can delay me from mailing for a couple of business days. I ship first class with tracking info. I cannot realistically get everyone a tracking number PM'd to them but if you are worried about your jig please PM me and we will track it.
_________________________________________________________________________________________________________________

Here are the installation instructions, please read them if you buy the jig they really do help it go quickly.

UNPLUG THE SAW.

Remove the thumb screw on the left side of the clamp, catch and save the little nut that falls out from underneath, you'll need it later.

Rock the clamp assembly until it comes out, set aside.

The hole that used to have the pivot in it (right side) will need to be threaded. The supplied bolt is fully capable of doing it but
you must keep it vertical as you tighten it. Place the bolt in the jig and then put the jig on the saw.
Carefully align and with downward pressure tighten the Allen head bolt until it just touches the top of the jig.

**OR** use the supplied bolt and thread the base from below. Once the bolt has cut the threads remove and install from the top.

Install the left side bolt and the nut you saved from earlier.

I would strongly suggest you not remove the saw unit from the base, the return spring can be difficult to reinstall.

Make sure the saw blade is tight and not on backwards, this is the cause of almost all slow cutting and saw burn out.

Next lower the saw blade and slide the jig up to about the thickness of a 3x5" index card (.010") from the side of the blade.
Let the saw blade go up while holding the jig in place. Snug the right bolt.

Now push the left side of the jig back towards the saw's hinge slightly. The jig should be SLIGHTLY crooked when you look down on it.
Tighten the left bolt then the right.

Clamp, bolt, screw or otherwise secure the saw to the work bench.

*********Spray with a light lubricant.************

Cut a test piece of brass. I like to cut them to about 1.365" to 1.370" and then finish trim them.

If the brass is too long or short for your taste adjust the jig towards or away from the blade as needed.

If the brass mouth is cut at an angle, adjust the left side of the jig as needed to correct.

Before you turn on the saw and start cutting a bunch of cases, practice the insertion of brass several times to get a feel for it.

Sizing the brass first will often speed things up, it removes the little bulges that can slow ejection. Also run a swab or bore brush through the jig periodically to wipe out trash.

As you use and lube the jig, case operation will get noticeably smoother and faster.


About 4% of these saws have a different base, you may need to add a few washers under the bolt heads or 1% of the saws add a nut to the bottom of the right bolt.

PLEASE NO PAYPAL GIFTS!!!


Last edited by vz58 on Wed Sep 17, 2014 8:38 pm, edited 187 times in total.

Top
 Profile  
 
 Post subject: Re: Case cut off tool
PostPosted: Sun Sep 16, 2012 11:13 pm 
Offline
Silent But Deadly
User avatar

Joined: Fri Sep 14, 2012 9:37 am
Posts: 196
Location: Concho, AZ
Just 1 thing I'ld like to know about that little fixture. What's the clearance between the I.D. of the fixture and the O.D. of the case?

Just curious because not all cases are round, I run into a lot of them kinda squashed and or mangled and they just might not fit.

_________________
If you don't learn from history your doomed to repeat its mistakes

Link to my other sales page: http://castboolits.gunloads.com/forumdisplay.php?117-Grumpa


Top
 Profile  
 
 Post subject: Re: Case cut off tool
PostPosted: Sun Sep 16, 2012 11:43 pm 
Online
Silent But Deadly
User avatar

Joined: Fri Jul 29, 2011 11:57 am
Posts: 892
Location: Smack dab in the middle of NC
Grumpa, thanks for asking. If the case is wider than the rim at any point (or bowed) they will not work . Under that they should be good to go.


If I can figure it out I will post a quick video on this.

Not my video (whose is it??) But its my jig, much better then my 30 second clip.

http://www.youtube.com/watch?v=2rySmFSn ... ata_player


Last edited by vz58 on Tue Apr 02, 2013 3:23 am, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: Case cut off tool
PostPosted: Mon Sep 17, 2012 12:23 am 
Offline
New Member

Joined: Wed Sep 05, 2012 5:49 pm
Posts: 1
Sure blows the hell out of my wood block!!!! I'll take one if you have any left!!!!! Very cool.


Top
 Profile  
 
 Post subject: Re: Case cut off tool
PostPosted: Mon Sep 17, 2012 8:54 am 
Online
Silent But Deadly
User avatar

Joined: Fri Jul 29, 2011 11:57 am
Posts: 892
Location: Smack dab in the middle of NC
Space holder


Last edited by vz58 on Tue Jan 29, 2013 4:47 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Mon Sep 17, 2012 9:40 am 
Offline
Silent Operator
User avatar

Joined: Sat Feb 18, 2012 7:20 pm
Posts: 63
Location: N.W. Ohio
Very slick, I like it.

Good job.

All the best...Bob.


Top
 Profile  
 
PostPosted: Mon Sep 17, 2012 2:56 pm 
Offline
Silent But Deadly
User avatar

Joined: Fri Sep 14, 2012 9:37 am
Posts: 196
Location: Concho, AZ
Well at least it answers that question, now here's another :shock: . Yeah I know , on your lengths, is there a way to adjust the length or is it pre-set? With my set-up I cut them to 1.365 right off the bat, but they aren't the only things I make out of 223 brass either, and I can get just under 600pcs an hour but that's going kinda fast for me. I haven't looked at the video yet (soon but I'm terribly busy right now) and if the chop saw is on continuously it over-heats, I've gone thru 2 already trying that and have to resort to turning it on and making my cut and turning it off and so on.

Yes I do a tremendous amount of volume with those cheap P.O.S.'s and in 6mo I've gone thru 4 already. Still trying to find the best way to do the cuts and be productive at the same time, without it costing a small fortune.

_________________
If you don't learn from history your doomed to repeat its mistakes

Link to my other sales page: http://castboolits.gunloads.com/forumdisplay.php?117-Grumpa


Top
 Profile  
 
PostPosted: Mon Sep 17, 2012 3:55 pm 
Online
Silent But Deadly
User avatar

Joined: Fri Jul 29, 2011 11:57 am
Posts: 892
Location: Smack dab in the middle of NC
There is room for adjustments, but as there are variations in these saws I cant 100% say all saws will be able to adj to all sizes. I cant imagine it wouldnt but...

As for your production rate surely it will be more depending onyour drive.

We have run these saws for hours. The only heat issue was on a backwards blade.


Top
 Profile  
 
PostPosted: Mon Sep 17, 2012 4:23 pm 
Offline
Member

Joined: Tue May 31, 2005 4:26 am
Posts: 15
Location: West
I'll take one if there are any left. Please PM me your payment details and I will PP you. Thanks


Top
 Profile  
 
PostPosted: Mon Sep 17, 2012 4:55 pm 
Offline
Member

Joined: Fri Jun 01, 2012 7:47 pm
Posts: 44
Location: central florida
I want one too!
You take Paypal?
PM me on how to get one if ya got any on hand.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1133 posts ]  Go to page 1, 2, 3, 4, 5 ... 114  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: 2B1H, ANDYHUNTER13, armexman, babyeagle, binder, blackoutbullets, BRAVO1NINER, Charlie_Zulu, coast2coast, contitrac, cs86, DPS1331, gabe1519, gaterbait7, gds, Google [Bot], Guest762, Hardrockshot, HotHolster, IdahoFireman, IslandTimes, jimmyheadgear, juls300, kamoto, Ken70, kg4kpg, manchumedic, monzahunter, mrlumu, punisher12b, Reloadimizer, RiflemanWI, S4area51, ScottieB, spectra, Squid300, superspirit, tjkane1, twostepct, vz58, willisjf07 and 131 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group