JP Custom Logo Hogue Pistol Grip
JP Enhanced 9mm AR Bolt
9mm Silent Captured Spring
Magpul RVG
Rule #1
Starting my 9mm Carbine SBR Build
Moderators: gds, bakerjw, renegade
-
- Silent But Deadly
- Posts: 248
- Joined: Fri Jun 14, 2013 8:16 am
- Location: Upstate SC
Re: Starting my 9mm Carbine SBR Build
Dystaxia
Will you be using a suppressor with your build?
Will you be using a suppressor with your build?
Re: Starting my 9mm Carbine SBR Build
Yes, I have an Osprey 45.jimmyheadgear wrote:Dystaxia
Will you be using a suppressor with your build?
-
- Silent But Deadly
- Posts: 248
- Joined: Fri Jun 14, 2013 8:16 am
- Location: Upstate SC
Re: Starting my 9mm Carbine SBR Build
Will it screw on without any mods? Nothing will change with the blow back system, correct? I told a friend about my build, which is similar to yours, and he said I'd need a fixed barrel spacer for the suppressor.Dystaxia wrote:Yes, I have an Osprey 45.jimmyheadgear wrote:Dystaxia
Will you be using a suppressor with your build?
Isn't that only needed when you use a DI setup?
- Dolomite_Supafly
- Silent But Deadly
- Posts: 3017
- Joined: Fri Oct 30, 2009 7:03 am
- Location: East Tennessee
- Contact:
Re: Starting my 9mm Carbine SBR Build
The 9mm build is blowback, not direct impingement (DI). The direct thread replaces the Nielsen device because if you leave the Nielsen device on a gun that is not a pistol it may damage the suppressor. The Nielsen device is needed for most pistols to temporarily remove the weight of the suppressor from the end of the barrel so the gun will cycle. If not then the weight of the suppressor will prevent the barrel from tilting and unlocking. Because the barrel of an AR does not tilt there is no need to use a Nielsen device.jimmyheadgear wrote:Will it screw on without any mods? Nothing will change with the blow back system, correct? I told a friend about my build, which is similar to yours, and he said I'd need a fixed barrel spacer for the suppressor.Dystaxia wrote:Yes, I have an Osprey 45.jimmyheadgear wrote:Dystaxia
Will you be using a suppressor with your build?
Isn't that only needed when you use a DI setup?
BTW, there are a few pistols who do not need a Nielsen device because their barrels do not tilt when they unlock. The most common is the Berretta 92 and clones.
WWW.thegunmilitia.com
Come join the militia!
Come join the militia!
Re: Starting my 9mm Carbine SBR Build
Sent off the lower today to the engraver. I was able to pick up barrel from the post office at the same time, bonus;
5.5 Inch, 1/2x28 Thread Black Melonite Finish Barrel
Rule #1
5.5 Inch, 1/2x28 Thread Black Melonite Finish Barrel
Rule #1
Re: Starting my 9mm Carbine SBR Build
Kinda makes me want a 9mm upper for my Spike's lower
I do not reply to posts with horrific grammar errors.
I do not reply to posts concerning the case mouth dent.
I do not reply to posts concerning the case mouth dent.
Re: Starting my 9mm Carbine SBR Build
I love the Qcircle10 products!
So far your build is eerily similiar to mine; main difference being I went with the glock lower instead of the colt. Vltur upper, 5.5 Qcircle10 barrel, jp spring, kns pin set, JP bolt...
I used the odinworks rail though
https://www.primaryarms.com/Odin_Works_ ... -05-km.htm
Anyways, good luck, this will be a great little gun for you! Hopefully you enjoy yours as much as I enjoy mine!
So far your build is eerily similiar to mine; main difference being I went with the glock lower instead of the colt. Vltur upper, 5.5 Qcircle10 barrel, jp spring, kns pin set, JP bolt...
I used the odinworks rail though
https://www.primaryarms.com/Odin_Works_ ... -05-km.htm
Anyways, good luck, this will be a great little gun for you! Hopefully you enjoy yours as much as I enjoy mine!
-
- Member
- Posts: 21
- Joined: Sat Oct 04, 2014 5:08 pm
Re: Starting my 9mm Carbine SBR Build
Care to share a pic?AndyT wrote:I love the Qcircle10 products!
So far your build is eerily similiar to mine; main difference being I went with the glock lower instead of the colt. Vltur upper, 5.5 Qcircle10 barrel, jp spring, kns pin set, JP bolt...
I used the odinworks rail though
https://www.primaryarms.com/Odin_Works_ ... -05-km.htm
Anyways, good luck, this will be a great little gun for you! Hopefully you enjoy yours as much as I enjoy mine!
Re: Starting my 9mm Carbine SBR Build
theguyonthecouch wrote:Care to share a pic?AndyT wrote:I love the Qcircle10 products!
So far your build is eerily similiar to mine; main difference being I went with the glock lower instead of the colt. Vltur upper, 5.5 Qcircle10 barrel, jp spring, kns pin set, JP bolt...
I used the odinworks rail though
https://www.primaryarms.com/Odin_Works_ ... -05-km.htm
Anyways, good luck, this will be a great little gun for you! Hopefully you enjoy yours as much as I enjoy mine!
and with my form 1 suppressor:
Who is online
Users browsing this forum: Amazon [Bot] and 38 guests