Looks like SA is finally in the game.
http://www.springfield-armory.com/
New Springfield Armory Ar!!
Moderators: gds, bakerjw, renegade
New Springfield Armory Ar!!
"Trust me...I know what I'm doing."
Re: New Springfield Armory Ar!!
After months of teaser advertising their a little late to the party.
Yawn
Yawn
Re: New Springfield Armory Ar!!
I would take a AR with Bravo Company furniture over a Magpul equipped AR any day of the week. It would be more ergonomic.
The specs look pretty squared away and gives you a very good bang for the buck.
It is a 700.00 AR that IMO can compete in the 500.00-1,200.00 market.
The specs look pretty squared away and gives you a very good bang for the buck.
It is a 700.00 AR that IMO can compete in the 500.00-1,200.00 market.
Industry Pro Staff for Dynamic Research Technologies When One Shot is All You Get www.drtammo.com https://www.facebook.com/drtammo/
Join the Revolution http://youtube.com/watch?v=3_Xnx3BFuLk
Join the Revolution http://youtube.com/watch?v=3_Xnx3BFuLk
Re: New Springfield Armory Ar!!
https://www.thetruthaboutguns.com/2016/ ... ory-saint/A-Game wrote:I would take a AR with Bravo Company furniture over a Magpul equipped AR any day of the week. It would be more ergonomic.
The specs look pretty squared away and gives you a very good bang for the buck.
It is a 700.00 AR that IMO can compete in the 500.00-1,200.00 market.
Enjoy your melted handguard.
Re: New Springfield Armory Ar!!
+1TMD wrote:After months of teaser advertising their a little late to the party.
Yawn
I do not reply to posts with horrific grammar errors.
I do not reply to posts concerning the case mouth dent.
I do not reply to posts concerning the case mouth dent.
Re: New Springfield Armory Ar!!
Is it made in Croatia? jab jab
If it doesn't splatter, shatter, burst, boing or explode, it's not worth shooting.
Re: New Springfield Armory Ar!!
That would be a fitment issue with the handguard touching the A2 gas block. It didn't melt for any other reason. I've baked Magpul and BCM polymer in the oven and it takes over 400 degrees to melt like that.TMD wrote:https://www.thetruthaboutguns.com/2016/ ... ory-saint/A-Game wrote:I would take a AR with Bravo Company furniture over a Magpul equipped AR any day of the week. It would be more ergonomic.
The specs look pretty squared away and gives you a very good bang for the buck.
It is a 700.00 AR that IMO can compete in the 500.00-1,200.00 market.
Enjoy your melted handguard.
I've burned my hand shooting a Magpul MOE handguard equipped rifle because of the steel screws that run the length of the bottom midline.
Industry Pro Staff for Dynamic Research Technologies When One Shot is All You Get www.drtammo.com https://www.facebook.com/drtammo/
Join the Revolution http://youtube.com/watch?v=3_Xnx3BFuLk
Join the Revolution http://youtube.com/watch?v=3_Xnx3BFuLk
Re: New Springfield Armory Ar!!
Yeah, 8 mag dumps would probably stress out just about any polymer part, and there's no way to keep the HG off the gas block, that steel plate that the HG clips into contacts it directly.A-Game wrote:That would be a fitment issue with the handguard touching the A2 gas block. It didn't melt for any other reason. I've baked Magpul and BCM polymer in the oven and it takes over 400 degrees to melt like that.TMD wrote:https://www.thetruthaboutguns.com/2016/ ... ory-saint/A-Game wrote:I would take a AR with Bravo Company furniture over a Magpul equipped AR any day of the week. It would be more ergonomic.
The specs look pretty squared away and gives you a very good bang for the buck.
It is a 700.00 AR that IMO can compete in the 500.00-1,200.00 market.
Enjoy your melted handguard.
I've burned my hand shooting a Magpul MOE handguard equipped rifle because of the steel screws that run the length of the bottom midline.
I do not reply to posts with horrific grammar errors.
I do not reply to posts concerning the case mouth dent.
I do not reply to posts concerning the case mouth dent.
Re: New Springfield Armory Ar!!
Then it is a problem BCM is going to have to redesign unless it was a fluke. I have found that because Magpul polymer is thicker than the polymer BCM uses in its stocks BCM stocks have a higher risk of deformation when heat is applied like when they are cured after painting.
They may end up having to scrap the PKMR, re-design it, put a different handguard or they are going to have to put a low profile gas block and handguard on the rifle.
BCM should have done multiple heat cycles to find the upper limits of what the handguards can handle and S.A. would have done the same.
They may end up having to scrap the PKMR, re-design it, put a different handguard or they are going to have to put a low profile gas block and handguard on the rifle.
BCM should have done multiple heat cycles to find the upper limits of what the handguards can handle and S.A. would have done the same.
Industry Pro Staff for Dynamic Research Technologies When One Shot is All You Get www.drtammo.com https://www.facebook.com/drtammo/
Join the Revolution http://youtube.com/watch?v=3_Xnx3BFuLk
Join the Revolution http://youtube.com/watch?v=3_Xnx3BFuLk
- Netpackrat
- Silent But Deadly
- Posts: 661
- Joined: Mon Oct 26, 2015 2:06 am
Re: New Springfield Armory Ar!!
Weeks of hype, and it's another AR...
Who is online
Users browsing this forum: Google [Bot] and 17 guests