Share your 300 Blackout Loads here>
Moderators: gds, bakerjw, renegade, bamachem
Re: Share your 300 Blackout Loads here>
Anyone tried titegroup?
Re: Share your 300 Blackout Loads here>
titegroup is most likely too fast of powder.
- m1garand30064
- New Member
- Posts: 3
- Joined: Mon Nov 16, 2009 10:07 pm
- Location: Roswell, GA
Re: Share your 300 Blackout Loads here>
Awesome! What powder and what charge are you using?libertyman777 wrote:My upper cycles 178 Amax and 180 grain SP like a champ but it has a pistol length gas system and and adjustable gas block. But I think the gas system length has more to do with its' consistency because I haven't touched the gas block and it runs both subsonic and supersonic in these weights. But I may be wrong.m1garand30064 wrote:Has anyone found a good subsonic recipe using the 175 grain mil spec bullets from Widener's? http://wideners.com/itemdetail.cfm?item ... |1081|1161
I have a ton of these sitting around and hope that you guys can give me some good news!!
I would like to get a good subsonic load using these bullets, but if I am forced to use 200 grain + rounds to get a consistent round that cycles my gun I guess I'll have to go that route.
Paul
- Twistomatic
- Silent Operator
- Posts: 51
- Joined: Sun Dec 18, 2011 11:02 pm
- Location: Texas
Re: Share your 300 Blackout Loads here>
Here is mine,
16" Wilson Combat Recon stainless carbine gas length 1/8 twist.
The following is my load:
150 grn FMJ bullet
17 grains of H110
Winchester Primer / small rifle
Case: I cut down and formed my own from mixed commercial and military brass. I used Lee dies to help form my brass. You can use factory brass if you want. I just wanted to try my own formed brass for the results.
Case length before loading is 1.360. I used a factory Remington case as a guide for my formed brass.
side note: Lee dies do not have load data when you get them at least mine did not. I got mine last week from MidwayUSA.
16" Wilson Combat Recon stainless carbine gas length 1/8 twist.
The following is my load:
150 grn FMJ bullet
17 grains of H110
Winchester Primer / small rifle
Case: I cut down and formed my own from mixed commercial and military brass. I used Lee dies to help form my brass. You can use factory brass if you want. I just wanted to try my own formed brass for the results.
Case length before loading is 1.360. I used a factory Remington case as a guide for my formed brass.
side note: Lee dies do not have load data when you get them at least mine did not. I got mine last week from MidwayUSA.
Twistomatic and some Black Magic.
- libertyman777
- Silent But Deadly
- Posts: 209
- Joined: Sun Feb 17, 2008 10:46 am
Re: Share your 300 Blackout Loads here>
m1garand30064 wrote:Awesome! What powder and what charge are you using?libertyman777 wrote:My upper cycles 178 Amax and 180 grain SP like a champ but it has a pistol length gas system and and adjustable gas block. But I think the gas system length has more to do with its' consistency because I haven't touched the gas block and it runs both subsonic and supersonic in these weights. But I may be wrong.m1garand30064 wrote:Has anyone found a good subsonic recipe using the 175 grain mil spec bullets from Widener's? http://wideners.com/itemdetail.cfm?item ... |1081|1161
I have a ton of these sitting around and hope that you guys can give me some good news!!
I would like to get a good subsonic load using these bullets, but if I am forced to use 200 grain + rounds to get a consistent round that cycles my gun I guess I'll have to go that route.
Paul
Hornady 180 Spire Point Flat Base
2.26 OAL
10.4 grains A1680
1010
1060
949
976
995
1018
989
1007
1061
970
Hornady 180 Spire Point Flat Base
2.26 OAL
10.2 grains A1680
931
955
948
936
972
1007
995
973
994
IIRC, I threw the same powder charge for the 178. Primers were CCI. These shot just under 2 MOA.
Remember............ You're special, unique, one of a kind....................just like everyone else.
Re: Share your 300 Blackout Loads here>
Location: Benton AR
Temp: 48F
Altitude: 423ft
Rifle: Remington Micro 7
Silencer: AAC cyclone
Bullet: Hornady 208 a-max for all groups listed
Note: went with 3 shot groups at 50yds
Grains Powder COL AVG FPS Extreme spread FPS
10.8 1680 2.24 1048 27
The left hole in this pic had two bullets go through it.
Grains Powder COL AVG FPS Extreme spread FPS
10.9 1680 2.24 1085 38
Note: seating depth change
Grains Powder COL AVG FPS Extreme spread FPS
10.8 1680 2.11 1166 24
Grains Powder COL AVG FPS Extreme spread FPS
10.9 1680 2.11 1186 5
I am obviously trying for a subsonic hunting load. Went out yesterday and 11.1 and 11.2grains with COL of 2.14 was too fast. Did some searching to see how big of a deal bullet seating depth has on performance and found arguments from both camps. My gun likes 2.24 more than sticking it deaper in the case.
Temp: 48F
Altitude: 423ft
Rifle: Remington Micro 7
Silencer: AAC cyclone
Bullet: Hornady 208 a-max for all groups listed
Note: went with 3 shot groups at 50yds
Grains Powder COL AVG FPS Extreme spread FPS
10.8 1680 2.24 1048 27
The left hole in this pic had two bullets go through it.
Grains Powder COL AVG FPS Extreme spread FPS
10.9 1680 2.24 1085 38
Note: seating depth change
Grains Powder COL AVG FPS Extreme spread FPS
10.8 1680 2.11 1166 24
Grains Powder COL AVG FPS Extreme spread FPS
10.9 1680 2.11 1186 5
I am obviously trying for a subsonic hunting load. Went out yesterday and 11.1 and 11.2grains with COL of 2.14 was too fast. Did some searching to see how big of a deal bullet seating depth has on performance and found arguments from both camps. My gun likes 2.24 more than sticking it deaper in the case.
Re: Share your 300 Blackout Loads here>
Here is my load data close to what cliff developed:
130 grain pulled federal barrier blind sost
18 grains h110
Oal 2.050.... The crimp to the notch closest to the tip
No chrono data but primers looked fine and rifle cycles were fine
Out of a 16" DS arms chrome-moly barrel.
Had to shoot at 25m to sight my rifle in, but shots were on top of each other.
130 grain pulled federal barrier blind sost
18 grains h110
Oal 2.050.... The crimp to the notch closest to the tip
No chrono data but primers looked fine and rifle cycles were fine
Out of a 16" DS arms chrome-moly barrel.
Had to shoot at 25m to sight my rifle in, but shots were on top of each other.
Re: Share your 300 Blackout Loads here>
Looks good. I wasn't impressed with the accuracy when crimped in the bottom groove. I think I load a few crimped in the top groove and check accuracy. I'll load some of your loads and mine and try to chronograph this week.WhoDat wrote:Here is my load data close to what cliff developed:
130 grain pulled federal barrier blind sost
18 grains h110
Oal 2.050.... The crimp to the notch closest to the tip
No chrono data but primers looked fine and rifle cycles were fine
Out of a 16" DS arms chrome-moly barrel.
Had to shoot at 25m to sight my rifle in, but shots were on top of each other.
Cliff
FPD, USN Retired, NRA Lifer
FPD, USN Retired, NRA Lifer
Re: Share your 300 Blackout Loads here>
Haven't seen much in the way of data for a Noveske 8" Rogue Hunter/Diplomat. Here's what I have so far.. Unfortunately, the new chrony's still en route.
Mostly function checking to get a feel for the l'il beast.
Using SMK 220's, Rem brass and CCI primers. All thru a SWR Omega 30 Suppressor.
H110-
My comparator was borrowed and is yet to be returned.
Can't really say about accuracy as I was free handing it mostly. But at 30ish yards picking off little 2" pieces of broken ceramic tile I had propped up for a bit of target practice while I was piddlin were easy enough to hit.
Looking forward to some real range/load development time here shortly. This was in the little back yard range. More components on the way. Thanks for your help so far, fellas.!! d:^) Schneeks..
Mostly function checking to get a feel for the l'il beast.
Using SMK 220's, Rem brass and CCI primers. All thru a SWR Omega 30 Suppressor.
H110-
- 9.7gr (Didn't note the clicks) was sub but didn't cycle the action.
10.5gr Went super and still didn't cycle the action.???
- 21.5cl/11.4gr Sub/Cycles/No lockback.
22.5cl/12gr Sub/Cycles/Locks back
23.5cl/12.6gr Super
My comparator was borrowed and is yet to be returned.
Can't really say about accuracy as I was free handing it mostly. But at 30ish yards picking off little 2" pieces of broken ceramic tile I had propped up for a bit of target practice while I was piddlin were easy enough to hit.
Looking forward to some real range/load development time here shortly. This was in the little back yard range. More components on the way. Thanks for your help so far, fellas.!! d:^) Schneeks..
Outside the wire it's just us chickens, dig?
Re: Share your 300 Blackout Loads here>
Powders faster than A1680 will not reliably cycle, load data for H110 is fine for bolt guns.
Todd
Who is online
Users browsing this forum: No registered users and 249 guests