Boyd’s stocks

Moderators: gds, bakerjw, renegade

User avatar
cwlongshot
Silent But Deadly
Posts: 1077
Joined: Sat Oct 18, 2014 7:53 pm
Location: Connecticut

Re: Boyd’s stocks

Post by cwlongshot » Sun May 17, 2020 11:39 am

WOOHOO!! Glad ya got it working man!!

I was shooting mine last night... with 90g FTX!!!! These never ever came close to "feeding" before and they where not slick feeding. But push forward stop pull back a tad and push closed worked that way for fifty rounds shooting suppressed steel last afternoon!! These where trail boss 4.5g loads and nice n quiet and super accurate insode the 50 yards we shot.

I have four ladders loaded for todays range trip. Hoping I find a acc node... H335, 30-31.2230 & H110 powders.

CW
RARR 300 BLK
Ares SCR 300 BLK
TROY "other" 300 BLK
DSI based build w/18” 300 BLK (Neutered fixed mag)



I PROUDLY SUPPORT LAW ENFORCEMENT & OUR TROOPS!!

BulletFlight for Android
BlogSarge
Silent But Deadly
Posts: 1286
Joined: Mon Oct 21, 2013 11:10 pm

Re: Boyd’s stocks

Post by BlogSarge » Tue Jun 02, 2020 12:32 am

CW, when you used the Tru-oil, did you sand off the entire stock’s factory finish? Or did you just sand where material needed to be removed?

I’m thinking of re-contourng mine around the trigger/thumbhole area because it feels too blocky to me, like your did for you.

User avatar
cwlongshot
Silent But Deadly
Posts: 1077
Joined: Sat Oct 18, 2014 7:53 pm
Location: Connecticut

Re: Boyd’s stocks

Post by cwlongshot » Tue Jun 02, 2020 11:49 am

Hello Sarge!!


I sanded everywhere. But on orig finish only to scuff up. I sanded everywhere smoother and smoother as well.

As long as orig finish is in good shape it should be just fine.

Good luck

CW
RARR 300 BLK
Ares SCR 300 BLK
TROY "other" 300 BLK
DSI based build w/18” 300 BLK (Neutered fixed mag)



I PROUDLY SUPPORT LAW ENFORCEMENT & OUR TROOPS!!

BlogSarge
Silent But Deadly
Posts: 1286
Joined: Mon Oct 21, 2013 11:10 pm

Re: Boyd’s stocks

Post by BlogSarge » Wed Jun 03, 2020 12:01 am

Thanks. I might spend a few quality hours with sand paper and bourbon!

User avatar
cwlongshot
Silent But Deadly
Posts: 1077
Joined: Sat Oct 18, 2014 7:53 pm
Location: Connecticut

Re: Boyd’s stocks

Post by cwlongshot » Thu Jun 25, 2020 7:31 am

BlogSarge wrote:
Wed Jun 03, 2020 12:01 am
Thanks. I might spend a few quality hours with sand paper and bourbon!
I like the results. Good luck on yours!!

https://youtu.be/MEFkj_ZlIlw

CW
RARR 300 BLK
Ares SCR 300 BLK
TROY "other" 300 BLK
DSI based build w/18” 300 BLK (Neutered fixed mag)



I PROUDLY SUPPORT LAW ENFORCEMENT & OUR TROOPS!!

BlogSarge
Silent But Deadly
Posts: 1286
Joined: Mon Oct 21, 2013 11:10 pm

Re: Boyd’s stocks

Post by BlogSarge » Sat Jun 27, 2020 10:43 am

Looks nice cw.

Mine came out OK, shoots well and all but it was a bit more work than I planned on.The only issue left is the poor feeding of some longer rounds. But that was an issue with the original gun/stock also.

User avatar
cwlongshot
Silent But Deadly
Posts: 1077
Joined: Sat Oct 18, 2014 7:53 pm
Location: Connecticut

Re: Boyd’s stocks

Post by cwlongshot » Mon Jun 29, 2020 8:07 am

I find its the barrel. I am tempted to remove it and polish Like a AR PCC barrel opening. The factory leaves it square just breaking that corner and polishing to a mirror might make all the difference.

I would love for my NOE TL 310-178 RD bullet
To feed. It shoots SO FLIPIN well single loaded!!

CW
RARR 300 BLK
Ares SCR 300 BLK
TROY "other" 300 BLK
DSI based build w/18” 300 BLK (Neutered fixed mag)



I PROUDLY SUPPORT LAW ENFORCEMENT & OUR TROOPS!!

BlogSarge
Silent But Deadly
Posts: 1286
Joined: Mon Oct 21, 2013 11:10 pm

Re: Boyd’s stocks

Post by BlogSarge » Fri Jul 03, 2020 10:08 am

Thanks CW, I’ll have to give that a shot. SHort rounds like the Hornady 190 Sub-X do well, but the 208 loads hang up.

Post Reply