Wonder what would have happened if it had been a cast bullet...jryock wrote:
300BLK chambered and fired in a 5.56mm barrel. The projectile is stretched out, the magazine blew out, and damaged the gun.
Source: https://www.facebook.com/#!/JCWeaponry
300BLK in a 5.56 barrel
Moderators: gds, bakerjw, renegade
Re: 300BLK in a 5.56 barrel
- JeffWard
- Silent But Deadly
- Posts: 237
- Joined: Tue Jul 15, 2014 12:13 pm
- Location: St Pete, FL
- Contact:
Re: 300BLK in a 5.56 barrel
Sharpie makes oil-based paint pens that work GREAT. I just labeled all my 300BLK mags with a large red "300" near the top, right were the mag goes into the mag well.
JW
JW
Guns are tools designed for dirty work both competitive and defensive. If I meet someone with a well worn gun, I hope their barrel is pointed the same direction as mine if the lead starts flying...
Re: 300BLK in a 5.56 barrel
Hmm. He must have used a short load. More powder and that bullet would just shoot right out .
Good thing I only have enough money to shoot one caliber.
Good thing I only have enough money to shoot one caliber.
Re: 300BLK in a 5.56 barrel
That's what I do. Goof Off takes the paint right off without harming the mag when/if I need to switch. I also have been putting "super" or "sub" on them with the projectile weight.JeffWard wrote:Sharpie makes oil-based paint pens that work GREAT. I just labeled all my 300BLK mags with a large red "300" near the top, right were the mag goes into the mag well.
JW
Lately I have been taking a few wraps of hockey tape on the mags for grip; then I just paint pen on that. It makes the switches even easier.
Re: 300BLK in a 5.56 barrel
double post...
Last edited by hunter2 on Thu Aug 07, 2014 6:40 am, edited 1 time in total.
Re: 300BLK in a 5.56 barrel
The way it's cut out so nice it makes me wonder if it was done on purpose for a demonstration piece.
- plant.one
- Silent But Deadly
- Posts: 6823
- Joined: Tue Jun 23, 2009 8:31 pm
- Location: Oakland County, MI
Re: 300BLK in a 5.56 barrel
Guest762 wrote:The way it's cut out so nice it makes me wonder if it was done on purpose for a demonstration piece.
the cut was done as a demonstration , i seriously doubt that anyone would fire a 308 through a 5.56 intentionally just to see if it would kaboom or not
Reloading info shared is based on experiences w/ my guns. Be safe and work up your loads from published data. Web data may not be accurate/safe.
This disclaimer will self destruct in 10 seconds.
This disclaimer will self destruct in 10 seconds.
Re: 300BLK in a 5.56 barrel
I don't know if it was or wasn't but r&d is accomplished somehow. I would be willing to bet good money that those cut outs weren't done in someone's garage.
Re: 300BLK in a 5.56 barrel
But what was his group size?
Did he crono it?
Is he sharing his load data?
If it was a 5.56 chamber, would it be ok?
Can I use a 223 silencer if I shoot 300 BLK out of a 223?
Did he crono it?
Is he sharing his load data?
If it was a 5.56 chamber, would it be ok?
Can I use a 223 silencer if I shoot 300 BLK out of a 223?
- plant.one
- Silent But Deadly
- Posts: 6823
- Joined: Tue Jun 23, 2009 8:31 pm
- Location: Oakland County, MI
Re: 300BLK in a 5.56 barrel
Guest762 wrote:I would be willing to bet good money that those cut outs weren't done in someone's garage.
i think there was another thread about having a barrel cut like that after it happened to a member on here. the word i remember reading out was using a Wire EDM to acheive the process.
Reloading info shared is based on experiences w/ my guns. Be safe and work up your loads from published data. Web data may not be accurate/safe.
This disclaimer will self destruct in 10 seconds.
This disclaimer will self destruct in 10 seconds.
Who is online
Users browsing this forum: No registered users and 87 guests