Good evening!
I can't seem to find a while lot of info on this round...has anyone had stabilization issues with it? Anyone run it through a chronograph?
Any reason to avoid it? It would be shot out of my 9" AAC 1:7 twist and my wife's 8" Aero precision 1:8 twist, both with suppressors on them.
Seller and Bellot 200 grain subsonic
Moderators: gds, bakerjw, renegade
-
- New Member
- Posts: 2
- Joined: Mon Apr 02, 2018 10:04 pm
Re: Seller and Bellot 200 grain subsonic
Not really the answer you are looking for but with two of you shooting consider handloading.
-
- New Member
- Posts: 2
- Joined: Mon Apr 02, 2018 10:04 pm
Re: Seller and Bellot 200 grain subsonic
Unfortunately due to where we live, and both of us working and living extensively overseas, reloading isn't a practical option for us during the next few years.
-
- Member
- Posts: 26
- Joined: Mon Nov 06, 2017 10:58 am
Re: Seller and Bellot 200 grain subsonic
I’ve run S&B 200gr subs with good results out of my 16” 1:8. Haven’t tried on the 9” 1:7 but suspect they will be gtg. No issues with stability or cycling.
If II recall correctly, they were running up around 1080ish out of the 16” but I will confirm that tonight. Out of a 9” you should have no issues keepthing them sub and stable that is your goal. They run fairly clean as well, and are pretty darn inexpensive.
***Edit***
Here are my Chrono numbers for these last time I was out using the 16”...
1032 / 1018 / 1015 / 1001 / 1000
If you are planning on running these through a can, you should be in pretty good shape. That being said, I would definitely run them without the can first and not risk your cans on an 80cent round.
If II recall correctly, they were running up around 1080ish out of the 16” but I will confirm that tonight. Out of a 9” you should have no issues keepthing them sub and stable that is your goal. They run fairly clean as well, and are pretty darn inexpensive.
***Edit***
Here are my Chrono numbers for these last time I was out using the 16”...
1032 / 1018 / 1015 / 1001 / 1000
If you are planning on running these through a can, you should be in pretty good shape. That being said, I would definitely run them without the can first and not risk your cans on an 80cent round.
Re: Seller and Bellot 200 grain subsonic
I am fairly new to the 300 BLK, but not ARs.
So far, I really like shooting the 200 grain Sellier and Bellot out of an unsuppressed 14.7 inch barrel. I will second that it is fairly clean and it has been reliable.
My biggest impression is that it is very quiet without a suppresser out of the longer barrel.
So far, I really like shooting the 200 grain Sellier and Bellot out of an unsuppressed 14.7 inch barrel. I will second that it is fairly clean and it has been reliable.
My biggest impression is that it is very quiet without a suppresser out of the longer barrel.
Re: Seller and Bellot 200 grain subsonic
I shoot this round thru my 9", 10.5" and 16" 300bo uppers. It has f=performed good in all of them both suppressed and unsuppressed. Stays quite in all three lengths.
Re: Seller and Bellot 200 grain subsonic
Have people continued having good results with this ammo? And how is the brass, does it work well for reloading afterwards? Looking to start out with some bulk ammo but in a brass I can reload from there.
-
- Silent But Deadly
- Posts: 248
- Joined: Fri Jun 14, 2013 8:16 am
- Location: Upstate SC
- BoomerVF14
- Silent But Deadly
- Posts: 217
- Joined: Thu Jan 08, 2015 8:03 pm
Re: Seller and Bellot 200 grain subsonic
I picked up about 80 rounds of S&B at the range from a nearby lane who was going to discard them so I knew they were once-fired. They measured a little long so most of them I had to trim a couple thounsandths to get to 1.360". Neck tension was a consistent .003" and the primers (all tested good with the Ballistic Tools primer pocket gauge) went in smooth as glass compared to my re-man'd FC/LC stuff.
I realize S&B is on the "potential problems" list on this forum, but so far I haven't had any issue except one. One single case had a weird issue where something got hung up in my Forster press, and the COAL/CBTO numbers were way off all the others. I couldn't figure out what the problem was so I just pulled/discarded that case and all the others were fine.
Who is online
Users browsing this forum: No registered users and 130 guests