Search found 1527 matches

by 20X11
Thu Jul 16, 2020 9:34 am
Forum: AR15s
Topic: Newbie barrel threading question
Replies: 5
Views: 350

Re: Newbie barrel threading question

Thread pattern isn't important, bore size is. You need a .308 muzzle device threaded to match your barrels thread pattern. I would not use an adapter.
by 20X11
Wed Jul 15, 2020 10:10 pm
Forum: AR15s
Topic: Newbie barrel threading question
Replies: 5
Views: 350

Re: Newbie barrel threading question

As long as your muzzle device has a hole larger than .308 for the bullet to pass through, you are fine.
by 20X11
Tue Jul 07, 2020 11:45 am
Forum: AR15s
Topic: Bolt group
Replies: 12
Views: 610

Re: Bolt group

How far up does the buffer retainer stick up into the end on the tube...compared to the lower that works?
by 20X11
Mon Jul 06, 2020 7:54 pm
Forum: AR15s
Topic: Bolt group
Replies: 12
Views: 610

Re: Bolt group

ok, sounds like a bad BCG...does the groove on the bottom of the BCG run the full length, or did it get "short machined"?
by 20X11
Mon Jul 06, 2020 7:42 pm
Forum: AR15s
Topic: Bolt group
Replies: 12
Views: 610

Re: Bolt group

Does the BCG go all the way back without a magazine in the rifle?
by 20X11
Sun Jul 05, 2020 2:13 pm
Forum: AR15s
Topic: AR 300BLK won’t chamber the first round from full clip
Replies: 21
Views: 1214

Re: AR 300BLK won’t chamber the first round from full clip

Rockingj wrote:
Sun Jul 05, 2020 1:16 pm
golfindia wrote:
Sun Jul 05, 2020 9:18 am
Too many shells in your clip .....
30 rounds in a 30 round magazine is too many?
...
Yes, 30 rounds of 300BLK in a Magpul 30 rnd magazine designed for the 5.56 round IS TOO MANY.
by 20X11
Sun Jul 05, 2020 10:26 am
Forum: Handloading
Topic: Dillon neck flaring powder funnel
Replies: 10
Views: 4209

Re: Dillon neck flaring powder funnel

As mentioned in that thread, the only time most reloaders would flare rifle brass is for cast bullets. Typically chamfer/deburr will allow copper bullets to seat without issue. Now, if you are using a Mr. Bullet feeder on a progressive press, this may not be the case, but you should follow the instr...
by 20X11
Sun Jun 21, 2020 7:36 pm
Forum: AR15s
Topic: AR 300BLK won’t chamber the first round from full clip
Replies: 21
Views: 1214

Re: AR 300BLK won’t chamber the first round from full clip

Load the same magazine with .223 rounds...note the vertical ribs near the front in relation to the bullet. Now load the magazine with 300blk rounds...see the issue with the vertical ribs on the bullet? On a full mag, that changes the height of the stack of bullets.
by 20X11
Sat Jun 20, 2020 10:53 am
Forum: Main Discussion Area
Topic: New Here
Replies: 2
Views: 154

Re: New Here

My 10.5 psa runs like a clock. if you don't reload - START, if you do reload - UPGRADE your press. You gonna need more ammo.
by 20X11
Fri Jun 12, 2020 3:30 pm
Forum: Main Discussion Area
Topic: New to 300blackout world
Replies: 11
Views: 781

Re: New to 300blackout world

I like to plink with 125gr Speer TNTs...they shoot great out of my 7" as well as 16" barrels. Sig Sauer makes a 125gr round that works extremely well, but I can load my own far cheaper.