Search found 29 matches
- Tue Oct 19, 2021 7:22 pm
- Forum: Main Discussion Area
- Topic: Gas port issues?
- Replies: 10
- Views: 6372
Re: Gas port issues?
As was previously mentioned, different combinations will produce different results. My advise is to buy the parts that float your boat. Assemble the parts and then make adjustments were needed to fit your needs. I put together a pistol with Ballistic Advantage 10.5" Premium barrel. I intended t...
- Sat May 16, 2020 4:07 pm
- Forum: Silencer Discussion
- Topic: Accuracy problems with suppressor
- Replies: 13
- Views: 11926
Re: Accuracy problems with suppressor
You mention accuracy issue but didn't post group size change. Is it really an accuracy issue or is it a point of impact shift?
- Tue Feb 26, 2019 7:21 pm
- Forum: Main Discussion Area
- Topic: Down the rabbit hole I go!
- Replies: 12
- Views: 4446
Re: Down the rabbit hole I go!
During this build I've not had the greatest of luck with vendors, except the ones that post here. Tried to order a carbine buffer tube end plate only to have the vendor cancel the order and refund since they apparently didn't have it in stock as listed. Optic's Planet shipped me a 15" handguard...
- Thu Feb 21, 2019 4:44 pm
- Forum: Main Discussion Area
- Topic: Redding 300 AAC Blackout Trim & Forming Die use in Co-Ax Press?
- Replies: 4
- Views: 2473
Re: Redding 300 AAC Blackout Trim & Forming Die use in Co-Ax Press?
So I finally have my answer, yes it works. The form die body is long enough to contact the shell holder jaws and fully form the case. I've only formed up a little over 20 cases but the die works beautiful. So my Co-Ax press saved me the expense of buying an extended shell holder.
- Tue Feb 12, 2019 1:13 pm
- Forum: Main Discussion Area
- Topic: Redding 300 AAC Blackout Trim & Forming Die use in Co-Ax Press?
- Replies: 4
- Views: 2473
Re: Redding 300 AAC Blackout Trim & Forming Die use in Co-Ax Press?
If you are not going to trim, only form, you may be able to set the die as needed and screw the lock ring on to the bottom. I am not familiar with the Co-ax enough to say for certain. Actually the lock ring isn't tightened to the press but only to the die body. The dies are allowed to free float so...
- Tue Feb 12, 2019 11:48 am
- Forum: Main Discussion Area
- Topic: Redding 300 AAC Blackout Trim & Forming Die use in Co-Ax Press?
- Replies: 4
- Views: 2473
Re: Redding 300 AAC Blackout Trim & Forming Die use in Co-Ax Press?
Well, here is my thought on how or why this may work. The trim/form die is short and when threaded into a standard press it is too short for the shell holder to make contact thus the need for an extended shell holder. The Co-ax design is different and the shell holder plate comes much closer to the ...
- Mon Feb 11, 2019 3:27 pm
- Forum: Main Discussion Area
- Topic: Redding 300 AAC Blackout Trim & Forming Die use in Co-Ax Press?
- Replies: 4
- Views: 2473
Redding 300 AAC Blackout Trim & Forming Die use in Co-Ax Press?
The title pretty much says it all. In my haste to buy equipment to start forming 300 Blackout brass I overlooked the need for an extended shell holder for use with the Redding Trim & Forming die. I tried searching the net to see if anyone else had tried this combination but hit a blank. Since I'...
- Sun Feb 10, 2019 7:45 pm
- Forum: New Product Announcements and Good Deals
- Topic: 220 grain expanding subsonic Bullets are back
- Replies: 12
- Views: 11481
Re: 220 grain expanding subsonic Bullets are back
Go to the linked site posted on page 1 and it is all women's clothing so I guess they are out of the bullet business!
- Fri Feb 08, 2019 1:58 pm
- Forum: Handloading
- Topic: Anyone else try the redding form and trim die?
- Replies: 8
- Views: 2232
Re: Anyone else try the redding form and trim die?
Sure, take advantage of an old geezer and have him spend is money. They used to have one in stock but not any longer.bangbangping wrote:Midway has one of these on clearance for $40.
Thanks!
- Thu Feb 07, 2019 8:57 pm
- Forum: General Gun Talk
- Topic: BCA got raided yesterday - by ICE, for identity theft by some of its employees
- Replies: 15
- Views: 5777
Re: BCA got raided yesterday - by ICE, for identity theft by some of its employees
Since when is an identity theft investigation handled by Homeland Security/ICE? I used to work in a prosecutor's office, then later a county jail. Since all the time. If you know what you are talking about all of the above stuff actually makes perfect sense. BCA had some employees that were illegal...