Search found 277 matches
- Thu Nov 02, 2023 10:16 am
- Forum: Accessories
- Topic: Optics
- Replies: 19
- Views: 25573
Re: Optics
CW, have a picture of the reshaped Spike Camp? I put one on my 783 chambered in 30.06
- Mon Jun 12, 2023 9:46 am
- Forum: General Ammo Discussion
- Topic: Now AAC 110gr V-Max thread (Factory 300blk pulldown data)
- Replies: 5
- Views: 945
Re: Factory 300blk pulldown data
Use this search engine for postings on this site. Don't remember who created it but it's handy.
https://cse.google.com/cse?cx=017035176 ... tl9hapdoi0
https://cse.google.com/cse?cx=017035176 ... tl9hapdoi0
- Mon Aug 08, 2022 6:30 am
- Forum: Handloading
- Topic: 266 grain cast bullet, the Dolomite special
- Replies: 226
- Views: 70271
Re: 266 grain cast bullet, the Dolomite special
CFE Blk will work good, starting at 9 grains then working down should get you there. The designer of the bullet recemonds IMR 4227 as a choice powder for this bore rider.
- Thu Sep 09, 2021 12:06 pm
- Forum: Handloading
- Topic: Sub-X COAL for AR-style auto loader
- Replies: 2
- Views: 1412
- Wed Jan 27, 2021 7:08 am
- Forum: Accessories
- Topic: Optics
- Replies: 19
- Views: 25573
Re: Optics
Recently I have been shooting a 1-10 Atibal-X on my 300 Blk. Switched from a 1-4 since I couldnt pin point those dimes at 100yrds.
- Sun Jan 24, 2021 1:17 pm
- Forum: Main Discussion Area
- Topic: 250 Hornady A Tip, or what happens when the bullet is longer than min COL?
- Replies: 13
- Views: 9288
Re: 250 Hornady A Tip, or what happens when the bullet is longer than min COL?
What about IMR Red? I have used it with a Domolite special 265grn.
As usual dellet interesting work. We should talk about front Ignition some time.
As usual dellet interesting work. We should talk about front Ignition some time.
- Thu Jan 14, 2021 1:31 pm
- Forum: Main Discussion Area
- Topic: Something to make you smile.
- Replies: 1
- Views: 1331
- Tue Jan 12, 2021 1:33 pm
- Forum: Classified Ads
- Topic: 3D Printed Chute for Cutting Down 223/5.56 Brass
- Replies: 24
- Views: 10486
Re: 3D Printed Chute for Cutting Down 223/5.56 Brass
With pushing brass from left to right what holds it at the correct distance for the cut? My design feeds from R to L and uses a pin to index the case. Interested in ordering one just dont like to have my finger under the saw motor during the cut.
- Thu Nov 19, 2020 7:15 am
- Forum: Main Discussion Area
- Topic: Better accuracy from homemade converted LC brass using Lee collet die.
- Replies: 113
- Views: 38743
- Mon Nov 16, 2020 10:44 am
- Forum: Handloading
- Topic: Hornady 190 gr Sub-X load data
- Replies: 65
- Views: 60913
Re: Hornady 190 gr Sub-X load data
Tried some Lil Gun and deeper seating on the sub-x bullet. 100 yrd groups shot consecutive no cryno velocity as I am looking for best groups. If I could only shoot consistantly.