Search found 31 matches

by swedenelson
Sat Oct 31, 2015 10:53 pm
Forum: Casting
Topic: < - < - NEW 230 Grain Cast Sub Mold Available through NOE - > - >
Replies: 32
Views: 4339

Re: < - < - NEW 230 Grain Cast Sub Mold Available through NOE - > - >

Sorry
That code has been turned off - not for public use!

Bullet maker, maker
Al Nelson
by swedenelson
Sun Jul 20, 2014 10:45 am
Forum: Casting
Topic: 311 247Gr. FN Hollow Point Moulds
Replies: 48
Views: 15357

Re: 311 247Gr. FN Hollow Point Moulds

Have some more in stock - if you are interested
http://noebulletmolds.com/NV/index.php? ... 51qqq4krv4

Bullet maker, maker
Swede Nelson
by swedenelson
Tue Jun 10, 2014 10:12 am
Forum: Classified Ads
Topic: NOE 311 150Gr. SP (311414)
Replies: 1
Views: 835

NOE 311 150Gr. SP (311414)

Just ordered the tooling for the 311 150Gr. SP (311414) http://i69.photobucket.com/albums/i80/swedenelson/NOE_Bullet_Moulds_311_150Gr_SP_148_gr_Sketch.jpg Should run in about a week, get your order in if you want one You can order here: http://noebulletmolds.com/smf/index.php?topic=14.0 Bullet maker...
by swedenelson
Fri May 16, 2014 12:58 pm
Forum: Classified Ads
Topic: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!
Replies: 179
Views: 8261

Re: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!

yondering

Looking forward to your accuracy report

Bullet maker, maker
Swede Nelson
by swedenelson
Thu May 15, 2014 9:10 pm
Forum: Classified Ads
Topic: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!
Replies: 179
Views: 8261

Re: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!

Any loads worked up yet? Ran IMR4227 and H110 through QuickLoad and get the following Added Lil'Gun 5/16 COL 2.095" 20" barrel IMR4227 16.8Gr. 1993FPS 38053PSI 101.9% L.D. 17.5Gr. 2062FPS 42613PSI 105.6% L.D. H110 17.1Gr. 2047FPS 37434PSI 88.5% L.D. 17.8Gr. 2123FBS 42622PSI 92.1% L.D. Lil'Gun 16.8Gr...
by swedenelson
Thu May 15, 2014 9:57 am
Forum: Classified Ads
Topic: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!
Replies: 179
Views: 8261

Re: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!

Rushthezeppelin Using my mold over the last three days has got it seasoned (oxidized) real well You may have to use a very light smoking with a BIC lighter at first, but keep it very light. ryoko Others have suggested using "mold release" to paint in the vent lines Never tried it but it sounds like ...
by swedenelson
Wed May 14, 2014 4:20 pm
Forum: Classified Ads
Topic: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!
Replies: 179
Views: 8261

Re: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!

Pot temp. 700F - set and forget -
Use a fan to cool the blocks too.

Bullet maker, maker
Swede Nelson
by swedenelson
Wed May 14, 2014 12:43 pm
Forum: Classified Ads
Topic: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!
Replies: 179
Views: 8261

Re: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!

I have received two or three reports of "fining" with this bullet. We have ran this mould now for the last 3 days and this is our findings. The vent lines in the mould are within our standards and tolerance. The design of the nose is acting like a sprue funnel and the body of the bullet is acting li...
by swedenelson
Fri May 09, 2014 3:06 pm
Forum: Classified Ads
Topic: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!
Replies: 179
Views: 8261

Re: NOE 309 129Gr. PT

Its going to take a hard cast to get this to work!
50/50 (lino, wheel weighs) and maybe even water drop
The key word is "experimental"
Image

yondering
PM sent

Bullet maker, maker
Swede Nelson
by swedenelson
Sat May 03, 2014 11:16 pm
Forum: Classified Ads
Topic: NOE 309 129Gr. PT (CLOSED) Thanks for the orders!
Replies: 179
Views: 8261

Re: NOE 309 129Gr. PT

attila.

Didnt put the (.) on your handle - sorry
You should have it now

Bullet maker, maker
Swede Nelson